Two tools that keep prints and negatives under control
Darkroom work goes more smoothly when your hands stay out of the chemistry and your negatives stay flat. The Paterson Print Tongs and the Paterson Contact Printing Frame address those two jobs directly. The tongs give you a colour-coded way to move paper between developer, stop and fixer. The contact frame lets you proof a whole 35mm film onto one sheet so you can decide what to enlarge.
Neither tool is complicated, but each has a detail worth knowing before you start. Below is how to use them together in a simple darkroom session, with the tradeoffs the catalog makes clear.
What the Paterson Print Tongs give you
- Paterson Print Tongs - Set of 3: Supplied as a set of three colour-coded tongs, one each for developer, stop and fixer. Three tongs let you keep one tool per chemistry, reducing the chance of carrying developer into the stop bath or fixer into the developer.

Paterson Print Tongs - Set of 3 - Paterson Print Tongs - Set of 3: Textured side panels provide a firm grip, and the shaped shoulder is designed not to slip off the dish into the solution. A secure grip matters when you are moving wet paper in the dark; the shoulder helps the tong rest on the dish edge rather than sliding in.
How to use print tongs through a three-bath session
The tongs are colour-coded, so assign each colour to one bath before you turn off the lights. The steps below assume a standard developer-stop-fixer sequence; adjust the baths to your own process.
- Assign colours to baths: Decide which tong belongs to developer, which to stop, and which to fixer. Keep that assignment for the whole session so you never mix them up.
- Rest each tong on its dish: The shaped shoulder is intended to keep the tong from slipping into the solution. Set each tong on the edge of its own dish between uses.
- Move paper with the matching tong: Use the developer tong to lift the print from the developer, the stop tong for the stop bath, and the fixer tong for the fixer. The textured panels help you keep hold of wet paper.
- Keep one tong per chemistry: Do not swap tongs between baths mid-session. The colour coding only helps if you respect it.
A simple tradeoff: three tongs versus two
Many tong sets come as a pair, which forces you to choose which two baths get a dedicated tong. The Paterson set includes three, so developer, stop and fixer each get their own. That is the practical advantage here. The catalog does not specify tong length, material or heat resistance, so if you need those details for a particular dish or process, check before ordering.
What the Paterson Contact Printing Frame is built to do
- Paterson Contact Printing Frame - 35mm/8 x 10in: The PTP619 35mm model takes six strips of six exposures and proofs an entire 36-exposure film on a single 8 x 10 inch (20.3 x 25.4cm) sheet of paper. One sheet per roll makes it easy to compare frames and choose which negatives to enlarge.

Paterson Contact Printing Frame - 35mm/8 x 10in - Paterson Contact Printing Frame - 35mm/8 x 10in: A foam base and glass pressure plate hold the film and paper securely together. Good contact between negative and paper is what makes a contact proof sharp enough to judge.
- Paterson Contact Printing Frame - 35mm/8 x 10in: Negatives are positioned in slots on the mask, so strips sit in place before you close the frame. The mask keeps strips aligned and makes the proof easier to read.
Making a 35mm contact proof with the Paterson frame
Work in dim light or darkness according to your paper. The sequence below uses the frame’s supplied features; it does not replace your own exposure and development tests.
- Cut and arrange strips: The frame takes six strips of six 35mm exposures. Cut your developed and dried film into strips that fit the mask slots.
- Place strips in the mask slots: Lay each strip into its slot on the mask. The slots hold the negatives in position so they do not shift when you close the frame.
- Load paper on the foam base: Place a sheet of 8 x 10 inch (20.3 x 25.4cm) paper on the foam base, then close the glass pressure plate so film and paper are held together.
- Expose and develop as usual: Make your exposure, then develop the proof sheet using your normal tray process. Use the print tongs to move the proof through the baths.
- Read the proof and choose negatives: The resulting contact sheet lets you compare frames and pick which ones to enlarge.
What the catalog does not settle
The supplied information does not give exposure times, aperture settings, or a recommended paper grade for contact proofs. Those depend on your enlarger, paper and process, so run your own tests. The frame’s glass and foam are described as holding film and paper together, but no cleaning or storage instructions are provided; handle glass and foam according to your own darkroom practice.
For the tongs, the catalog confirms the three-tong set and the grip features but does not state dimensions or chemical resistance. If you use unusual chemistry, verify suitability with the manufacturer before relying on them.
Checkpoints before your next darkroom session
- Tongs assigned and resting on dishes: Each colour-coded tong should have one bath and sit on the dish edge, not in the solution.
- Film cut to fit the mask: Six strips of six exposures fit the PTP619 frame; cut accordingly.
- Paper size confirmed: The frame proofs onto 8 x 10 inch (20.3 x 25.4cm) paper.
- Proof developed and read: Use the contact sheet to select negatives for enlargement.



